3D Customizer

Uniholder

Universal customizable holder.

3D printing advisor CC BY-SA 4.0

Options

Print 3

What to generate: holder, DIN rail clip, both on one bed, or din_preview (clip shown mounted, for viewing only)

Largest overhang in degrees from vertical (60 default, 45 for weak part cooling) · Allowed: 40 – 60

Render quality

Size 5

inner = size of the item, outer = size of the finished holder

Width (X) · Allowed: 10 – 400

Depth (Y), front to back · Allowed: 10 – 400

Height (Z) · Allowed: 10 – 400

Clearance around the item on each side (inner mode) · Allowed: 0 – 10

Walls and edges 8

Side and front wall thickness · Allowed: 1.2 – 8

Back wall thickness (mounting side) · Allowed: 1.6 – 10

Floor thickness · Allowed: 0.8 – 8

Radius of the front vertical edges · Allowed: 0 – 40

Radius of the back vertical edges · Allowed: 0 – 40

Chamfer of the top edges · Allowed: 0 – 5

Chamfer of the edges on the print bed · Allowed: 0 – 3

Inner chamfer between floor and walls · Allowed: 0 – 10

Wall styles 5

open = cut down to a retaining lip, slot = narrow vertical slot

Hex pattern 5

Hexagon hole width across flats · Allowed: 3 – 40

Material between hexagons · Allowed: 1.2 – 10

Solid border at the wall ends · Allowed: 1 – 30

Solid band below the rim · Allowed: 0 – 50

Solid band above the floor · Allowed: 0 – 50

Front opening 5

Height of the retaining lip above the inner floor (open) · Allowed: 0 – 400

Width of the retaining edges left and right (open) · Allowed: 1.2 – 100

Radius of the lower corners of the opening (open) · Allowed: 0 – 50

Slot width (slot) · Allowed: 3 – 200

Height of the slot bottom above the inner floor (slot) · Allowed: 0 – 400

Back holes 8

Screw holes in the back wall; screws go in from inside the holder

Hole diameter (screw shank clearance) · Allowed: 3 – 10

countersink, counterbore and keyhole seat the head flush inside the back wall (it thickens as needed); plain leaves the head on the inner face

Screw head diameter including clearance (0 = 2 × hole diameter) · Allowed: 0 – 22

Number of hole columns · Allowed: 1 – 6

Number of hole rows · Allowed: 1 – 6

Horizontal hole spacing (0 = spread across the back wall) · Allowed: 0 – 300

Vertical hole spacing (0 = spread over the height) · Allowed: 0 – 300

Wings 9

Mounting wings, flush with the back face

Wing length beyond the side wall · Allowed: 8 – 100

Wing thickness · Allowed: 2 – 10

Wing height at the tip (0 = holder height) · Allowed: 0 – 400

bottom = wing stands on the bed; top = wing hangs from the rim with a support slope below

Hole diameter · Allowed: 3 – 10

slot = vertical slot for levelling

Holes per wing · Allowed: 1 – 4

Triangular gusset between wing and side wall

Pole mount 7

Mount on a round pole with zip ties (replaces the back holes)

Pole diameter · Allowed: 8 – 80

Included angle of the V-cradle; horizontal poles need at least 2 × (90 − max_overhang) · Allowed: 60 – 150

Number of zip ties · Allowed: 1 – 6

Zip tie width (standard ties: 5 mm) · Allowed: 2 – 14

Zip tie thickness (standard ties: 2 mm) · Allowed: 1 – 4

Clearance added to the tunnels on width and thickness · Allowed: 0 – 2

DIN rail clip 4

Bolt holes for the DIN rail clip in the back wall; the clip is a separate part (Print tab: part)

Bolts joining holder and clip (hole, head and nut sizes follow)

Height of the rail centreline on the holder (0 = automatic) · Allowed: 0 – 400

Clip width along the rail (0 = automatic) · Allowed: 0 – 100

3D preview

OpenSCAD
Generating the model… This takes a few seconds the first time.

Drag to rotate · right-drag to pan · scroll to zoom